For best results, use the Auto-iQ® programs. The pulses and pauses allow the ingredients to settle toward the blade assembly.
If ingredients are routinely getting stuck, adding some liquid will usually help. If making thick outputs in the TWISTi Pitcher, twist the built-in tamper counterclockwise continuously during blending to circulate ingredients.
When filling the cup, start with fruit or veggies, then leafy greens or herbs. Next add liquids or yogurt, then seeds, powders, or nut butters. Finally, add ice or frozen ingredients.
When filling the pitcher, start with frozen ingredients or ice, then add liquid(s) of choice. Next add leafy greens, seeds, powders, or nut butters, and finally add fruits or veggies.
This is normal and the unit is functioning properly. If you are using room-temperature ingredients to make nut butters, spreads, etc., output will be slightly warm due to friction of blending.
Smoothie bowls are thicker and spoonable, compared to smoothies, which are thinner and drinkable. Examples of spoonable recipes are smoothie bowls, hummus, pesto, and nut butters (thick outputs). Examples of drinkable recipes are smoothies, protein drinks, and green drinks.
Make sure the blade assembly is fully threaded, meaning there are no gaps between the blade assembly and the lip of the cup/pitcher. The blade assembly should be flush against the cup/pitcher.
Note: There will be no audible click when the blade assembly is properly installed.
Ensure the counter and feet of the unit are clean and dry before blending.
After processing, remove the pitcher lid, remove blended contents then remove the blade assembly.
You can use the motor base to clean the pitcher:
1. Rinse the pitcher and blade assembly under warm water after processing.
2. Screw on the blade assembly. Fill the pitcher with warm water up to the single-serve liquid line, add a couple of drops of dish soap, then install the lid.
3. Install the pitcher on the motor base. Select BOWL and twist the built-in tamper counterclockwise continuously while cleaning.
4. Once complete, empty contents and rinse pitcher under warm water.
With the pitcher handle facing you, place the lid on the pitcher with the red rectangle on the lid aligned with the red line on the pitcher. Push the lid down until it seals, then rotate the tab to the left until it clicks into place.
The motor base is powerful, and air will blow from the sides of the unit when in use. Move lightweight objects away from the unit before blending. Do not attempt to block vents.
If the display reads "--", install a container and the available program buttons will illuminate, indicating the unit is ready for use. Ensure the lid is fully engaged and the container has been rotated clockwise and clicked to lock into place.
Adding yogurt, powders, etc. will add additional flavors to your smoothie bowls.
For best blending results using the TWISTi pitcher, twist the tamper counterclockwise continuously during blending. Twisting the tamper will help circulate ingredients and bring them toward the blades. This will provide thicker and smoother outputs.
The tamper in the pitcher lid is not removable. Handwash the lid in warm soapy water or place in dishwasher for cleaning.
The TWISTi Pitcher and Single-Serve Cup can be used on any of the Auto-IQ programs. For spoonable outputs like smoothie bowls, hummus, or nut butters, use the SPREAD or BOWL Auto-IQ program. To create drinkable outputs such as smoothies, use the EXTRACT, SMOOTHIE, or FROZEN Auto-IQ programs.
For best results, use the built-in-tamper and TWISTi Pitcher for spoonable recipes.
Note: Smoothie and Spread function are not included on all models.
Use the drizzle hole to add liquid ingredients while processing. If results are too thick, open the drizzle hole cap and add more liquid. Keep the cap closed when processing liquids.
When creating smoothie bowls, use the liquid and max fill lines based on the intended serving size. For single serve, use the small bowl Liquid Fill and Max Fill lines. For 2 servings, use the large bowl Liquid Fill and Max Fill lines. Add liquid first, then frozen ingredients.
When installing the blades, turn enough to create a secure seal, but do not overtighten. If the blade assembly is stuck, use a dish towel to safely remove it.
If using the TWISTi Pitcher, remove the lid and contents after processing before removing the blade assembly.
Tip the unit forward from the back to easily disengage the suction feet.
The motor base is powerful. Loud noises are a normal occurrence, especially when blending frozen ingredients. If the noise seems louder than normal, add water until the cup is half full and install the blade assembly. Install the cup onto the motor base and run any program. Ensure the blades are spinning.
If the display reads "E1", the motor has been running for too long. As a safety feature, the unit cannot run for more than 3 consecutive minutes. Unplug the unit and let it cool for 15 minutes before running it again.
Make sure the unit is plugged in. If the unit is plugged in and no container is installed, the unit will display ‘- -’. The available programs will illuminate after placing a container on the base and rotating it clockwise until it clicks into place.
After processing, remove the pitcher lid, remove blended contents then remove the blade assembly.
You can use the motor base to clean the pitcher:
1. Rinse the pitcher and blade assembly under warm water after processing.
2. Screw on the blade assembly. Fill the pitcher with warm water up to the single-serve liquid line, add a couple of drops of dish soap, then install the lid.
3. Install the pitcher on the motor base. Select BOWL and twist the built-in tamper counterclockwise continuously while cleaning.
4. Once complete, empty contents and rinse pitcher under warm water.
For best results, use a dishwasher to remove stuck-on ingredients in the cup. You can also use the motor base to clean the cup:
1. Rinse the cup and blade assembly under warm water after processing.
2. Fill the cup halfway with warm water, then add 1 small drop of dish soap.
3. Screw the blade assembly onto the motor base and select BOWL.
Once complete, empty contents and rinse under warm water.
All parts except the base are dishwasher safe.
Make sure the unit is plugged in. If the unit is powered on and no container is installed, the unit will display ‘- -’. The available programs will illuminate after a container is properly installed on the base.
To get the thickest, most even results, twist the built-in tamper counterclockwise to push ingredients toward the blades, reducing the amount of liquid needed for blending.
The tamper in the pitcher lid is not removable. Handwash the lid in warm, soapy water or place in dishwasher for cleaning.
Press START/STOP or the currently active Auto-IQ program button again to stop the program.
Tip the unit forward from the back to disengage the suction feet.
Follow the instructions below to ensure all ingredients will be optimally processed by the blades and for best blending results. Leafy greens should be placed between the heavier ingredients such as fresh fruits, frozen fruits, and ice. When filling the Nutrient Extraction Cup, start with fruit or vegetables, then leafy greens or herbs. Next, add liquids or yogurt, then seeds, powders, or nut butter. Finally, add ice or frozen ingredients. When filling the pitcher, start with frozen ingredients or ice, then add liquid(s) of choice. Next add leafy greens, seeds, powders, or nut butter, and finally, add fruits or veggies.
To get the thickest, most even results, twist the built-in tamper counterclockwise to push ingredients toward the blades, reducing the amount of liquid needed for blending. We recommend using the build-in tamper for spoonable outputs such as smoothie bowl, nut butters, frozen treats , and dips and spreads. For best results, use BOWL or SPREAD* iQ program for SPOONABLE outputs and when TWISTING the built-in tamper.